Peaceful Deer with Sale-A-Bration Peaceful Prints DSP

Hello there! Thank you for joining me today for a very clean and simple stamping card created with the Peaceful Deer Bundle from the Holiday Catalog on page 26 and coordinating Peaceful Prints Designer Series Paper from the Sale-A-Bration Brochure on pages 8-9, which will retire in 2 days.

Be sure to pick up your bundle with some ink, card stock or adhesive, and get the Peaceful Prints DSP for FREE, when your order $50 in product, before taxes and shipping. Sale-A-Bration will be over in 2 short days.

I strongly encourage you to take advantage of all of the free products that coordinate beautifully with all of our product lines.

I’m personally going to hang onto the Counting Sheep stamp set and Sheep Dies. The popularity of these two Sale-A-Bration items hasn’t gone unnoticed. Think back to 2019 Sale-A-Bration Hey Chick stamp set and dies.

I also have a few extras of both of the above and will be holding a drawing very soon.

I will be featuring another Peaceful Deer Bundle with the Peaceful Prints DSP on Wednesday.

See the Peaceful Deer Bundle here and the Peaceful Prints Designer Series Paper here.

I did some partial dry embossing on the image panel with our Evergreen 3D Embossing Folder.

As always, your Supplies and Instructions, with measurements, are below.

I started out with an A2 Basic Black card base. I then cut a piece of Granite Gray CS from the largest Stitched Rectangle Die and partially embossed this panel with the Evergreen 3D Embossing Folder.

I stamped on the sentiment with Memento Tuxedo Black ink at the bottom center of the image panel that was not embossed.

I cut a piece of Peaceful Prints DSP from the plaid snowflake patten and wrapped this around the image panel to make pretty between the EF and sentiment.

This panel was adhered with Black Stampin’ Dimensionals.

BEFORE I applied the punched deer, I took my Wink of Stella Pen and splattered it around the card base and image/sentiment mat.

I punched out the deer and antlers from Basic Black CS and the Real Red and Basic Black buffalo pattern-ish Peaceful Prints DSP. I adhered the DSP deer and antlers to the Basic Black CS with liquid adhesive and carefully placed our Mini Black Stampin’ Dimensionals on the back. I traced around the punched images with a Basic Black Stampin’ Write Marker to clean and crisp up the edges of the deer, then adhered to the top center of the Granite Gray embossed image panel.

Lastly, I tied a length of Black and White Twine from Playful Pets Trim into a bow and adhered this to the center neck of the deer with a Mini Glue Dot.

I hope you enjoyed today’s project. Thank you for stopping by for a visit and have a great day!

 

 

 

 

 

 

 

Peaceful Deer Bundle (English) [156391] $36.00	Peaceful Prints 12″ X 12″ (30.5 X 30.5 Cm) Specialty Designer Series Paper [156628] $0.00	Stitched Rectangles Dies [151820] $35.00	Evergreen Forest 3D Embossing Folder [153576] $10.00
Playful Pets Trim Combo Pack [152466] $7.50	Clear Wink Of Stella Glitter Brush [141897] $8.00	Neutrals Stampin’ Write Markers [147158] $30.00	Tuxedo Black Memento Ink Pad [132708] $6.00
Basic Black 8-1/2″ X 11″ Cardstock [121045] $8.75	Gray Granite 8-1/2″ X 11″ Cardstock [146983] $8.75	Basic White 8 1/2″ X 11″ Cardstock [159276] $9.75	Basic White Medium Envelopes [159236] $7.50
Floral Grid Paper [150819] $11.75	Multipurpose Liquid Glue [110755] $4.00	Paper Snips [103579] $10.00	Paper Trimmer [152392] $25.00
Simply Shammy [147042] $8.00	Stamparatus [146276] $49.00	Stampin’ Cut & Emboss Machine [149653] $120.00	Mini Stampin’ Cut & Emboss Machine [150673] $60.00
Black Stampin’ Dimensionals Combo Pack [150893] $6.00	Stampin’ Dimensionals [104430] $4.00	Mini Stampin’ Dimensionals [144108] $4.00	Stampin’ Seal [152813] $8.00
Take Your Pick [144107] $10.00

 

 

 

1. Card base: A2 top-folding 4-1/4 x 5-1/2, Basic Black.
2. Image mat: Cut with the largest Stitched Rectangle die from Gray Granite CS and partially embossed with our Evergreen 3D Embossing Folder about 3-3/4 from the top.
3. DSP strip: Cut 1/2″ wide with just enough length past 3-7/8 to wrap around and adhere to the image panel, from Peaceful Prints DSP.